ALCPU Forums

Please post your core temp .95 screen shots.

Remember you can go to http://www.imageshack.us for free hosting.

Mine:

E4300 on GA-965P-DS3 (F10 bios) Running Vista 32
IT8718 monitoring chipset
FSB is reporting incorrectly... I have it set to 9x333
Right Now on Core0 Temps reported per app at 18% utilization are
SpeedFan4.32 - 32C, Core Temp 0.95 - 48C, TAT - 59C
Fire up TAT to 100% and then TAT and Core Temp match and SpeedFan reports 15C lower. e.g. 60C, 75C, 75C respectively.
What do I believe or rather what am I seeing?

Had my window wide open, managed to drop my temps to this.. normally its 18*C for Core 0 and 17*C for Core 1 on idle, highest ive had it go was 39*C core 0 / 35*C core 1... is that normal?

Machine is a Dell XPS 710..

I don't know which to believe. CoreTemp .94 and .95 are on there for the difference, though I think .95 is correct. If it is, my processor is running a bit hot methinks.

mmm 6x600

my Quad

steelkane wrote:my Quad
Core0 = 51 °C
Core1 = 48 °C
Core2 = 49 °C
Core3 = 48 °C
(Fahrenheit temps converter to Celsius)

Those temps are awfully high for a stock system. What HS/Fan are you using and how hot do they get when you're under load (like prime95 or 2x orthos)? Have a look at the thermal management section of this wiki article if you want more.

Did myself a 1984 edit. Im retarded hehe

lets pretend it never happened?

hot stuff.

P5WDH; BIOS 2205; QX6700 @ 3.0g
- CoreTemp v0.95
- loaded transcode with Sony Vegas 7.0e
- each ran for about 2.5 hours
- first at about 58% load
- second at 100% load
* measured with Fluke Mini62 IR and WattsUp Pro

58% LOAD:
http://www.esnips.com/doc/9a18164f-4145 ... DH-058Load

100% LOAD:
http://www.esnips.com/doc/416cfa39-0abf ... DH-100Load

@bichi - wow dude, 75 °C. You do know that TS for your chip is only 65 °C right? Here

You might wanna lap that chip and the base of your heatsink as well.

graysky - Which HS are you using?


I have SpeedFan set up with a temperature offset = 15 (Configure > Advanced tab > select INTEL core > enter temp offset)which gives me the same temp read out as CoreTemp and very close to TAT.

Mobo: EVGA 680i A1
CPU: Q6600 (stock)
RAM: 2GB OCZ PC28500 (@1066)

IDLE:



CPU 100%

DPC wrote:graysky - Which HS are you using?

I have a lapped U-120 Ex.

Hi could any one tell me the correct temp to read

on asus p5n-e sli mobo
2 gb kingston 677
8800gts
frezzer pro 7

100 % load
http://img149.imageshack.us/my.php?image=100loadmz4.jpg

0 % load
http://img182.imageshack.us/my.php?image=0loadsm1.jpg

thanks john

The coretemp (0.95.4) temps are correct. Notice it shows a tjunction of 100 which I believe it correct for your chip. Both 0.94 and speedfan incorrectly use the value of 85. Notice the temps are off by 15 °C (100-85 = 15).

Speedfan also gets the tjunction wrong for C2Q chips too.

thanks greysky

do you think my temps are abit high or fine

i use this machine just for gaming and had a p4 d945 before this is my first c2d

johnim wrote:thanks greysky

do you think my temps are abit high or fine

i use this machine just for gaming and had a p4 d945 before this is my first c2d

For a 4400 they would be right near the redline. Have a look at the Intel Processor Finder which shows 62 °C max.

Full Load...Using Thermaltake V1 Heatsink

I have just joined, this is my first post; and I'm also new to the core temp software. I noticed some pretty high temps on some of your computers. here are my temps I'm not doing much except listening to some music browsing on line and have my photoshop running. hope you can see my temps. By the way I have a custom water cooled system
Black ice radiator 100 its the 100 dollar one 2x 120 mm fans swiftnets cpu water block, pump, and resevoir. im also using the fluid xp hp blood red liquid , I'm also cooling my 8800 gts with a zalman 8800 gpu water block. I will try and stress my system and uplad the results next time. about 20C

[img][img]http://img295.imageshack.us/img295/2769/watercoolingtempsck3.th.jpg[/img][/img]